The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Tagis Yogor
Country: Haiti
Language: English (Spanish)
Genre: Photos
Published (Last): 21 February 2006
Pages: 375
PDF File Size: 19.18 Mb
ePub File Size: 10.51 Mb
ISBN: 537-4-67073-445-8
Downloads: 47061
Price: Free* [*Free Regsitration Required]
Uploader: Mezijas

Align 3gx pdf manual

I realise I’m going to probably have to modify the throttle curves and pitch curves later for thebut at least it’s a starting point. The more dampening effect, the smoother helicopter flies, but feels less direct.

Jul 25, If ava ilable, ensure the manuak functions are disabled in the transmitter: Faster servos are able to execute commands from the gyro at faster and higher precision. I spoke to the UK distributor today about my problem, and after a while we agreed that it seemed like the channel 6 servo was behaving as if it had a curve programmed to it.

Se “Trottle Calibration” at the end. Anyway, after talking a while, with the manual in front of me, it dawned on me that there’s an error in the manual; on page 21 it shows the 3Gx connection to a Futaba RFS receiver, which is what mine is, as being red, orange, yellow, green, blue, purple in that order, from channel 1 to 6.

With all channels stationary, move the transmitter elevator stick forward, and then back to center position. Press and hold the SET button while powering up the 3x. Dual axis plus rudder sensor dramatically improves swashplate and rudder correction precision compared to last generation 3G.


Where can I get the ‘dongle’?

The manual is embedded in the build instructions for the various Align kits. Reset throttle curve and pitch curve to default Incorrect neutral points will affect flight stability, and even lead to loss of control.

Should there be changes such as 3GX software update, pitch reconfiguration, or subtrim adjustments, the setup process must be repeated for the flybarless system. Jul 06, This setup mode sets the elevator gyro direction Tilt the helicopter forward and check if swashplate is tilting correctly toward the back.

Others have confirmed to me that they’ve set up their 3Gx without using a PC, so I think mine must be faulty. Introduction Brand new redesigned 3GX represents a new generation of multi function flybarless system. And yes you remove the bind plug while still powered, it sets fail safes, throttle etc.

Maunal excellent control feel will allow pilot of all skill levels to experience the perfect integration between 3GX and helicopter. The software is the manual. Gyro gain For radio with built in gyro gain settings, gain can be adjusted directly.

Password Please enter a password for your user account. Use a g3x email address manula you will not be granted access to the site. Jul 20, I also found this site: The throttle stick position where main pitch is 0 degree must be maintained. Microbeast or 3GX for Flybarless setup. Problem solved — the manual is wrong!! Push the throttle stick on transmitter to the maximum top, and in a few moments LED will maunal off and system power cycles, indicating the completion of setup process.

When I connect everything up to the 3Gx module, using a receiver battery, and putting it into DIR mode, the swash servo that’s in channel 6 behaves erratically. Preview the software and read everything and get familiarized with it. I mean like if you get a e super combo new, it comes with the connection wires? This completes the swashplate mixing type recognization process.


Align 3gx pdf manual | Model Flying

Should any changes made to the endpoints or subtrims on the transmitter in the future, the 3GX flybarless system initial setup must be performed again. Feb 08, My HK 3GX setup. Feb 04, Press the SET button to enter A. Just leave the servo horns off until your in setup and install them as close to level as poss at mid stick.

For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode non-heading lockor press and hold the SET button for 2 seconds. It is totally un helpful to every body to make statements of the form “When you have done this as many times as Aligm have you will know that you disregard the manual That’s a bit awkward for, if I read the CD correctly, I have to do that with the 3Gx installed in the heli, which means bringing alihn whole thing to my PC because I don’t have a laptop like they show in the CD.

In addition to transmitter, the anti-torque compensation feature can also be set through 3GX interface’s rudder parameter. With 3GX in operation mode, push rudder to left or right, and press the SET button for about a second.

This appears to come out of the manual.