ASTM E243 PDF

British Standards (BS) and American Standards (ASTM) relating to magnetic flux ASTM E Electromagnetic (eddy current) testing of seamless copper and. ASTM-E Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes – electromagnetic (eddy current) testing; NDT . Standard Number, ASTM E – Title, Standard Practice for Electromagnetic ( Eddy Current) Examination of Copper and Copper-Alloy.

Author: Malalkis Kazrashura
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Software
Published (Last): 27 October 2005
Pages: 296
PDF File Size: 6.44 Mb
ePub File Size: 2.14 Mb
ISBN: 605-3-15516-770-3
Downloads: 15182
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzragore

The values given in parentheses are mathematical conversions to SI units that are provided for information asmt and are not considered standard. See E for additional details regarding the in-situ examinations using internal probes.

Link to Active This link will always route to the current Active version of the standard.

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For your special needs, we can charge brazed fitting linesets with the refrigerant that will be used in your application see chart for refrigerants that are offered.

Quick, efficient and economical field installation Increased system efficiency using factory applied insulation Correct lengths for reducing waste Quality, consistency and economy All CerroSet tubing tested in accordance with ASTM E and provided with no detectable defects.

BoxArlingate Ln. For such applications, the technical differences associated with the use of internal probe coils ashm be recognized and accommodated. Any indication above the reject level that is believed to be irrelevant shall be regarded as unacceptable until it is demonstrated by re-examination or other means to be irrelevant see Historical Version s – view previous versions of standard.

ASTM Electromagnetic Inspection Standards

The liquid line is normally not insulated, but can be special ordered to be insulated. These procedures may be used for tubes beyond the size range recommended, upon contractual agreement between the purchaser and the manufacturer.

Link to Active This link will always route to the current Active version of the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  ALPHABET AERONAUTIQUE PDF

AIAWilson Blvd. Individual packaging and bulk packaging available. Our standard end finishing is available in three different options see chart.

copper tubing and other products

Since the density of eddy currents decreases nearly exponentially as the distance r243 the external surface increases, the response to deep-seated defects decreases. Brazed fittings – with or without refrigerant charge Flared ends The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Linesets Specialty Linesets.

Relevant indications are those which asfm from aetm discontinuities. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Individual linesets are packaged in cardboard inserts and packaged in a master carton. Irrelevant indications can mask unacceptable discontinuities. Swaged end 90 degree bend Plain end. Split system air conditioning Chilled water systems Warm water system. On-line eddy current examining would not be subject to end effect. All of our standard linesets are purged with dry nitrogen and capped to ensure a clean and non-oxidized tube prior to installation. The effect of foreign materials on the tube surface and signals due to tube e2243 are typical of the factors that must be considered.

Signals can be produced by discontinuities located either on the external or internal surface of the tube or by discontinuities totally contained within the walls.

For such applications, the technical differences associated with the use of internal probe coils should be recognized and accommodated. Note 1-This practice may be used as a guideline for the examination, by means of internal probe test coil systems, of installations using tubular products where the outer surface of the tube is not accessible. See Price Sheet for packaging multiples. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

We offer 1, different lineset combinations for quick, cost-efficient field installation of split system air conditioners and heat pumps. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

The effect of foreign materials on the tube surface and signals due to tube supports are typical of the factors that must be considered. For such applications, the technical differences associated with the use of internal probe coils should be recognized and accommodated.

  FUNDAMENTALS OF COMPUTER ALGORITHMS BY HOROWITZ SAHNI AND RAJASEKARAN PDF

Signals can be produced by discontinuities located either on the external or internal surface e423 the tube or by discontinuities totally contained within the walls. Signals can be produced by discontinuities located either on the external or internal surface of the tube or by discontinuities totally contained within the walls.

Standard Practice for Electromagnetic (Eddy-Current) Examination of Copper and Copper-Alloy Tubes

Any indication above the reject level that is believed to be irrelevant shall be regarded as unacceptable until it is demonstrated by re-examination or other means to be irrelevant e234 The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Currently there is no ASTM specification for insulated copper tube. Relevant indications are those which result from nonacceptable discontinuities.

In response to the demand for a quick, efficient and economical field method of installation for field connect split system air conditioners and heat pumps, Cerro offers a proven product. The illustration above shows a standard lineset with suction line insulated see chart for available insulation thickness. R A R RA. These procedures may be used for tubes beyond the size range recommended, upon contractual agreement between the purchaser and the manufacturer.

The effect of foreign materials on the tube surface and signals due to tube supports are typical of the factors that must be considered. This practice may be used as a guideline for the examination, by means of internal probe examination coil systems, of installations using tubular products where the outer surface of the tube is not accessible.

Since the density of eddy currents decreases nearly exponentially as the distance from the external surface increases, the response to deep-seated defects decreases.

BoxArlingate Ln.