KEITHLEY 196 MANUAL PDF
Visit us on the web at for more information: • Price Quotations • Drivers· Technical Specifications. Manuals and Documentation . Model System DMM Instruction Manual Rev. D. Manual Type: Primary User; Part Number: D. Release Date: Sep 17 View and Download Keithley DMM instruction manual online. 5 function autoranging digital multimeter. DMM Measuring Instruments pdf manual.
| Author: | Zulkikree Yokree |
| Country: | Uruguay |
| Language: | English (Spanish) |
| Genre: | Travel |
| Published (Last): | 18 September 2009 |
| Pages: | 472 |
| PDF File Size: | 5.64 Mb |
| ePub File Size: | 1.44 Mb |
| ISBN: | 139-6-73316-889-2 |
| Downloads: | 86287 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Kegal |
In this case, the exact value is assumed to be Use the following procedure to make DC voltage measurements.
Table liste the contact assignments for the bus, and Figure shows the contact configuration. Therefore, rninimize the loop area of the input leads and connect each signal at only one point.
Full text of “Keithley: KEI Instruction”
To speed the response to large step changes, the Model digital filter employs a “window” keitgley the displayed average. PDF -format schematics, 21 January A Model specification LabView library example for K DC current measurements from InA to 3A. The current value of M will now be displayed. When the data store is full. The following prompt will be displayed. The program will manuxl the store size to line 30enable the data store line 40turn on the data store output line 50and then request and display all readings lines Table keihhley typical times.
To change to a different measuring function, simply press the desired function button. Commands that affect instrument operation will trigger a reading when the command is executed. The secondary function of this but- ton is to enter the number 1.
Keithley System – In Stock, We Buy Sell Repair, Price Quote
The following message is displayed briefly when a short time error occurs: LrJ Input Terminals— The rear panel input terminals per- form the same functions as the front panel input terminals. Failure to use a grounded outlet may result in personal injury or death because of electric shock. This information will be helpful if you wish to verify that the instrument is operating in com- pliance keihtley its stated 16.
The serial poll byte contains important in- formation about internal functions, as described in paragraph 3. The cur- rent multiplexer status will then be displayed.
Per- form the following steps to use maual program: Each of these indicators is briefly described below. Model repair forum thread EEVBlog: Keithley firmware version B17 Keithley calibration data.
Determine the center frequency and bandwidth as ex- plained in the previous application Measuring Bandwidth. Cursor location is indicated by the bright, flashing display digit.
Entering an invalid value will result with the instrument using the power up default limit. Connect the test leads to the input of the Model and short them together. The number of readings in one time constant is equal to the filter value.
Keithley 196 DMM Instruction Manual
This schematics provided as is, reverse engineered by instrument owners. Disable zero and leave it disabled for the remainder of the ohms verification procedure. Under factory default conditions, measure- ments are referenced to IV or 1mA. The informa- tion is divided into the following sections: If the measured value falls within the high and low limits, the following message will be displayed: A typical connecting scheme for a multiple-instrument test set up is shown in Figure Once all readings have been requested, the unit will cycle back and begin again.
Trying to define a Translator word that already exists wtU cause an error message to be displayed briefly.
The fac- tory default LO limit is a negative full scale reading, with the actual value dependent on function and range. In- strument calibration is invalid. When the Model receives a DCL command, it will return to either the factory default conditions listed in Tables and or to the user saved default conditions.
Perform the following procedure to use the filter: Through the use of the H command, the front panel programs may be entered through commands given over the bus. User selectable values of L and H will be stored within the Model until the power is turned off unless saved by Program However, the dB pro- gram may be used to change the reference level.
OfX B Decimal point position is determined by the range that the instrument was on when this program was selected. If the alternate multiplexer status is desired, press one of the range buttons. HP Programming Example-Enter the following statements into the computer to perform the Model self-test: Also, the highest, lowest and average reading in a full buffer can be recalled by send- ing the appropriate U commands.
Set the Model to ACV and autorange.